Notes

1. NB: Applications shown may not apply to all models. General recommendations should be read in conjunction with the specific machine build and any other special requirements of the manufacturer including serial number.

Notes

1. NB: Applications shown may not apply to all models. General recommendations should be read in conjunction with the specific machine build and any other special requirements of the manufacturer including serial number.

Notes

1. NB: Applications shown may not apply to all models. General recommendations should be read in conjunction with the specific machine build and any other special requirements of the manufacturer including serial number.

Notes

• a. Do not mix coolants

1. NB: Applications shown may not apply to all models. General recommendations should be read in conjunction with the specific machine build and any other special requirements of the manufacturer including serial number.

Notes

• b. Viscosity selection criteria: Optimum viscosity, 60 cSt at operating temperature. Viscosity to remain between 50-110 cSt. at operating temperature; max cold temp peak, 110-200 cSt; min hot temperature peak, 30-50 cSt. Monograde oils are preferred but multigrades can be used if viscosity criteria cannot be met in prevailing operating conditions. ISO viscosity grade according to oil operating temperature; 12°C to 26°C, 32; 21°C to 32°C, 46; 29°C to 42°C, 68; 40°C to 51°C, 100; 48°C to 59°C, 150. Synthetic oils for temperatures below -20°C. Biodegradable & environmentally compatible oils recommended to ISO 15380.
• c. 2005, Tamrock factory fill oil, Shell Naturelle HFE 46 or HFE 68 synthetic ester. HFD-U synthetic, organic ester fluids for hazardous conditions also approved. Factory fill Tampere Plant, Fuchs Plantoflux 68-AT-S. Factory fill Lyon Plant, Condat D68. Also approved, Quaker Quintolubric 888-68. Guarantees not valid if these oils are not used. 20°C to 41°C, HM 46, 30°C to 50°C, HM 68

1. NB: Applications shown may not apply to all models. General recommendations should be read in conjunction with the specific machine build and any other special requirements of the manufacturer including serial number.

Notes

1. NB: Applications shown may not apply to all models. General recommendations should be read in conjunction with the specific machine build and any other special requirements of the manufacturer including serial number.

Notes

1. NB: Applications shown may not apply to all models. General recommendations should be read in conjunction with the specific machine build and any other special requirements of the manufacturer including serial number.

Notes

• d. 2005, Carriers with wet brakes, Models TC100, TC200, TC300, TC450, TC500, TC650, TC06, TC07, TC08, TC09, TC10, TC11, TC12

1. NB: Applications shown may not apply to all models. General recommendations should be read in conjunction with the specific machine build and any other special requirements of the manufacturer including serial number.

Notes

1. NB: Applications shown may not apply to all models. General recommendations should be read in conjunction with the specific machine build and any other special requirements of the manufacturer including serial number.

Notes

• e. Alternative recommendations, <0°C: Qualube Lithium EP 00
• f. Alternative recommendations, >0°C: Qualube Lithium EP 2 / Qualube Lithium Complex 2

1. NB: Applications shown may not apply to all models. General recommendations should be read in conjunction with the specific machine build and any other special requirements of the manufacturer including serial number.

Notes

• g. 2005, Gardner Denver/Tamrotor compressor. Mineral based engine oil or synthetic compressor oil can be used.Minimum engine oil viscosity, 7.0 cSt. If operating temperature is continuously >90°C, mineral based oil change is 300 hours or 600 hours with synthetic compressor oil
• h. Compressor, 2005 & -10°C to 30°C
• i. Alternative recommendations, 2005, -30°C to 40°C: Contact with our Technical Team
• j. Alternative recommendations, 2005, -20°C to 60°C: Contact with our Technical Team
• k. Alternative recommendations, Compressor, 2005, -20°C to 35°C: Contact with our Technical Team
• l. Alternative recommendations, Compressor, 2005, -5°C to 40°C: Qualube Endurasyn SS 10W-30 / Qualube Lawnmower 10W-30
• m. Alternative recommendations, Compressor, 2005, 0°C to 40°C: Qualube Eurofleet 20
• n. Alternative recommendations: Contact with our Technical Team

1. NB: Applications shown may not apply to all models. General recommendations should be read in conjunction with the specific machine build and any other special requirements of the manufacturer including serial number.

Notes

• o. Preferred grade: 0°C-40°C Contact with our Technical Team; -10°C-40°C Contact with our Technical Team

1. NB: Applications shown may not apply to all models. General recommendations should be read in conjunction with the specific machine build and any other special requirements of the manufacturer including serial number.

Notes

• p. Sandvik 795-1960

1. NB: Applications shown may not apply to all models. General recommendations should be read in conjunction with the specific machine build and any other special requirements of the manufacturer including serial number.

Notes

1. NB: Applications shown may not apply to all models. General recommendations should be read in conjunction with the specific machine build and any other special requirements of the manufacturer including serial number.

Notes

• q. Alternative recommendations, Shank Lubrication, 2005, -26°C to 0°C: Contact with our Technical Team
• r. Alternative recommendations, Shank Lubrication, 2005, -10°C to 15°C: Contact with our Technical Team
• s. Alternative recommendations, Shank Lubrication, 2005, 5°C to 40°C: Qualube Slideway 100
• t. Alternative recommendations, Shank Lubrication, 2005, 20°C to 50°C: Contact with our Technical Team
• u. Alternative recommendations, Shank Lubrication, 2005, 30°C to 60°C: Contact with our Technical Team
• v. Alternative recommendations, Shank Lubrication, 2005, 40°C to 70°C: Contact with our Technical Team

1. NB: Applications shown may not apply to all models. General recommendations should be read in conjunction with the specific machine build and any other special requirements of the manufacturer including serial number.

Notes

1. NB: Applications shown may not apply to all models. General recommendations should be read in conjunction with the specific machine build and any other special requirements of the manufacturer including serial number.